How the Scarva Earthstone ES70 Architectural Body Clay was born.
Our most popular clay loved by all.
We have the biggest and brightest selection of coloured decorating slips available on the market today.
See our best selling Raw Materials.
See our range of finished Glazed products.
Dragon Leadfree Glaze and Slip Stains.
See our best selling Stains and Colours.
Top selling underglaze brands Amaco, Nano Colours, Spectrum and more
See our best selling Underglaze Pencils & Crayons.
See our range of tools, equipment and resources.
See our range of wall extruders and accessories.
Everything in this section is reduced to clear. Grab a bargain! While stocks last!
Graded heating elements are supported on ceramic tubes in the walls and floor for efficient use of electricity.
Constructed from low thermal mass insulation brick with high grade backup insulation boards.
Powder coated 2mm zintec steel frame with rust resistant stainless steel architrave above the door.
Brick to brick door seal, no messy fibre.
Standard left hand door hinges with cost option for right hand
Door Spy Hole/vent and roof vent with damper.
Over-fire protection in conjunction with Potterycrafts controllers.
Designed for repeated high temperature firings to 1320°C (cone 11).
Three year warranty (excluding wear parts)
Back-up from our staff and network of independent service engineers.
Technical advice available on all aspects of using your kiln.
Potterycrafts Kilns are Made in Stoke-on-Trent, our skilled staff can call on over a 100 years accumulated knowledge of kiln building.
Firing capacity: 230 litres (8.1 cu ft).
Maximum Temperature: 1320°C (Cone 11)
Chamber dimensions mm: 420 wide x 610 deep x 885 high
External dimensions mm: 730 wide x 1090 deep x 1580 high
Power: 13.0 kW
Supply required: Single Phase-63 amps or 3 phase-20 amps per phase
Kiln Shelf size: 500 x 380 x 15mm - 1 batt per layer
Kiln Furniture Set:Not included in price of kiln
4 - P5485 BATTS 500 x 380mm
8 - P5518 PROPS 50mm
8 - P5519 PROPS 100mm
8 - P5521 PROPS 200mm
1 - P3380-01 BATT WASH (1Kg)
Controller included: CERA-2(2-programmemory each with 3 segments)
You can upgrade to CERA-5 , CERA-10 or CERA-10+ for marginal extra cost.
Additional Safety Equipment available for kilns(Links Below):
Kiln is made to order, delivery is approx 4-6 weeks (this will be confirmed when ordering)
KM207 Zintec Hood for P5120 and P5121 Lightmaster Kilns and P59445 and P5945 Heatworker Kilns.
The ventilation hood is designed to remove the excess heat from the kiln area.
It is positioned directly above the kilnand so it removes the air directly from around the kiln, as well as fumes from the flue, keeping the kiln area cooler.
The hood has a 150mm diameter spigot on top for connection to customers’ exhaust ducting.
We recommend connecting the spigot directly to the room extraction system or to an exhaust fan to prevent leakage of fumes intothe kiln room.
No electrical connections are required.
The Heatlock keeps the kiln door locked until the kiln has cooled to a safe temperature preventing damage to kiln door and eliminating risk of burning. The lock is discretely positioned adjacent to the interlock key under the door of our front loading kilns; it is operated by a small controller pre-set to lock at 60°C in the heating cycle and to unlock at 55°C on cooling. A warning light indicates when the door is locked, when the light goes out it is safe to open the kiln. The HeatLock is failsafe, if the power is turned off it remains locked, the door can only be opened when powered up and the temperature has dropped to 55°C.
The damper is pre-set to close when the kiln temperature reaches 550°C, it opens again when the kiln cools down to 200°C. There is no need to set the opening and closing temperature and no complicated controller as the temperatures are factory pre-set. The auto-damper eliminates the need to come back to the kiln during firing and removes the risk of the flue remaining open throughout the firing creating a potential hazard.
CERAcontrol is the latest development in a long series of controllers, they incorporate new software giving improved efficiency and ease of programming together with up to date safety and diagnostic features.
CERA-5+ has 5 programs each with delay start, 5 heating/cooling ramps, soak, cut off and program pause.
This controller gives the benefit multiple heating and cooling ramps for pottery firing where usually two programs are used, having five ramps allows for several heating and/or cooling phases in the program.
CERA-10 has 10 programs each with 10 segments. Delay start and program pause. Each segment has a heating/cooling ramp, a target temperature and a soak. This controller is ideal for firings where a range of programs are frequently used.
It can be used for any firing requiring close control over multiple heating and cooling ramps such as macro crystalglazes and for glass slumping and fusing.