Yumiko
from
Singapore
asks
I got recommended firing at 1240 as best result. How much shrink at this temp?
|
Scarva Replies:
|
The shrinkage would be approximately 10.7%, hope this helps.
|
Alison McfAdden
from
United Kingdom
asks
If I use decorating slips to paint onto the porcelain , I would then dry the clay and fire it then add a glaze, would this work and what temp would I fire to. Also could I add touches of a metallic sculptural glaze at the same time as adding the transparent glaze all over and then would I refire to what temperature?
|
Scarva Replies:
|
Thank you for your email. Yes simply apply decorating slips to greenware (unfired clay) let it dry then bisque fire to 1000oC. Once fired then apply glaze yes you can use as many glazes as you like however please be aware if you layer glazes the results can be unpredictable and may turn out different from whats pictured for example if you where to put the metallic glaze on top of the transparent it would bleed into it and could look amazing or it could look rubbish you will not know until you fire it, I would advise doing a few little test firings first before committing to your final piece. The glazes should be fired to their recommended firing temperature please make sure that both glazes are the same firing temperature. Alternatively if you wanted some gold highlights you could look at lustre yes it is more expensive but the results are very impressive, hope this helps.
|
Greg
from
United Kingdom
asks
I would like to create a textured thin wall of porcelain in the hope that when a light is shone from behind the texture would be shown. Would this clay be suitable or could you recommend an alternative porcelain which is more translucent?Thanks.
|
Scarva Replies:
|
Yes this is perfect fires very white also, hope this helps.
|
Tam
from
Portugal
asks
Hi. Is single firing possible with this clay? I intend to glaze the greenware piece with Botz liquid brush on glaze. Thanks.
|
Scarva Replies:
|
We do not recommend once firing. For best results bisque fire to 1000oC then glaze fire to desired temperature.
|
Emma
from
United Kingdom
asks
I would like to try this for making small ornaments, can I get away with firing only at 1080 twice at the most, also is it possible to use underglaze on this as green Ware?
Thanks
|
Scarva Replies:
|
Yes this is possible the clay will just not be matured.
|
Tam
from
Portugal
asks
Will this mature when fired at 1200C with a 30-minute soak? Thanks
|
Scarva Replies:
|
Yes this will work.
|
sharon
from
Australia
asks
What is the recommended firing temperature for ES170 Glacier Porcelain. That is, do you recommend firing at the lower or upper end of the range? Many thanks
|
Scarva Replies:
|
Hi, this body can fire to 1300°C, the higher you fire the more translucent it will become
|
Gill
from
United Kingdom
asks
Can this be used for larger sculptures? (normally use Flax paper porcelain 30-60cm)
|
Scarva Replies:
|
The Porcelain flazpaperclay is a very forgiving especially for handbuilding large work so difficult for any clay to compete with its unique properties. However there is no reason why you should not be able to make larger pieces using this clay body. Hope this helps.
|
Steve
from
United Kingdom
asks
I used a shared kiln that fires to 1060. is it ok to fire this to 1060 for the bisque?
|
Scarva Replies:
|
Yes that is okay.
|
Nurzehra
from
Netherlands
asks
Every porcelain has its own shrinking margin, I want to know what is this porcelains shrinking margin after drying and after firing.
Thank you very much in advance.
|
Scarva Replies:
|
The ES170 Glacier Porcelain has a shrinkage rate of approximately 18% at 1260°C. We do not have shrinkage rates for this clay at greenware. Hope this helps.
|
