Carlos
from
United Kingdom
asks
Could you give more details about the composition of this item? How much grams of gold is inside a 2g bottle? The gold used is 24 carat? Thanks!
Scarva Replies:
|
This gold lustre uses around 8% solids of 24 carat gold.
|
Sandra
from
United Kingdom
asks
Do I need to vent the kiln when using the platinum and gold lustres and for how long?
Scarva Replies:
|
I would recommend venting the kiln up to 200°C, hope this helps.
|
Blake
from
United Kingdom
asks
I'm putting this over porcelain. Do put this on after bisque firing? Or do I need to put this on after the item has been glaze fired?
Scarva Replies:
|
Ideally lustre would be applied to a glaze surface for best results, hope this helps.
|
Geoff
from
United Kingdom
asks
How many coats do I need to apply?
Scarva Replies:
|
One generous coat should work well.
|
Lucy
from
United Kingdom
asks
Firing temperature says between 700 & 800 degrees - if I'm using this lustre on glazed porcelain would you recommend firing closer to the 800 mark? or should this lustre still work at 700 degrees?
Scarva Replies:
|
I would fire to around 775oC on the controller.
|
Karen
from
United Kingdom
asks
Is gold lustre food safe?
Scarva Replies:
|
No it is not.
|
Jackie
from
United Kingdom
asks
Can this medium be painted on eggshells and left to dry without firing?
Thank you.
Scarva Replies:
|
No this will not work, it has to be fired in a kiln on something ceramic.
|
stephen
from
United Kingdom
asks
LM14 Gold Lustre. I propose to apply the lustre to white glazed porcelain and then fire it to 775 degrees C as prescribed.
Is it necessary to thin the lustre or apply it as supplied?
Scarva Replies:
|
Hi, the lustre is supplied in a ready to use state. Hope this helps!
|
Meg Burkill
from
United Kingdom
asks
I'm thinking of applying this over a crackle glaze, will this be ok?
Scarva Replies:
|
Yes this will work, lustres are applied onto fired ware so the glaze underneath will not matter.
|
Gabriele
from
United Kingdom
asks
Good Afternoon, I recently bought your Lustre. Could you pl advise me how to fire your gold lustre? what the temperature and how long in the kiln? Can I fire it with decals? Pl let me know
Thank you Very much
Gabriele
Scarva Replies:
|
Hi,
Lustre should be fired to around 750-780°C. I would suggest firing at about 150°C per hour, no need for a soak at the final temperature. There shouldn't be any problems firing decals with lustres, I would test first to make sure there isn't going to be any strange reaction in the kiln.
Hope this helps!
|
Margaret
from
United Kingdom
asks
Hello, is it necessary to clean the glazed surface with alcohol before applying this? if it is what type of alcohol do you recommend?
Scarva Replies:
|
No just make sure the surface is free from dust.
|
mimmi
from
Sweden
asks
How much gold is it in the Scarva Gold lustre?
How big is the difference between this lustre compared to the self-burnishing one?
Scarva Replies:
|
There are 8% gold solids in our gold lustre. The Self burnish gold contains the same amount however it turns out satin/burnish effect where the normal gold lustre is glossy.
|
sinead
from
Ireland
asks
How long can i leave the painted piece before firing?
Scarva Replies:
|
There is no limit of time a piece can be left for provided it is safe and out of direct sunlight.
|
Mimmi
from
Sweden
asks
Can this be used on glass?
Scarva Replies:
|
That will depend on what temperature your glass melts at, lustre has a a firing range of around 800°C, this is usually the temperature some glass begins to slump at.
|