Rohde ELS-480 S Pottery Kiln - email for quotation

Clear and extremely easy-to-operate control unit for use in workshops, schools and hobbies.

• 32 programs with 2 segments
• 2 controlled heating ramps / 1 controlled cooling ramp + soak per segment
• Soak periods up to 99 hours 59 mins
• Ramp rates from 1 to 999°/ hour + FULL
• USB interface and Wifi module to evaluate and save data with ROHDEgraph and ROHDE myKiln App
• Ideal for eramics use
• Programs can be altered while firing
• Program pause and advance facilities
• Keyboard lockable
• Delayed start facility – up to 99 hours 59 mins
• Power failure recovery
• Energy used display
• Setpoint display
• Alarm buzzer
• °C/°F operation
• USB interface for data logging

Temperature Programmer

• 32 programs each with up to 32 segments
• 1 controlled heating / cooling ramp + soak per segment
• 1 Programmable event
• Soak periods up to 99 hours 59 mins
• Ramp rates from 1 to 999°/ hour + FULL
• Ideal for glass or ceramics use
• Programs can be altered while firing
• Program pause and advance facilities
• Keyboard lockable
• Delayed start facility – up to 99 hours 59 mins
• Power failure recovery
• Energy used display
• Setpoint display
• Alarm buzzer
• °C/°F operation
• USB interface for data logging
• USB interface and Wifi module to evaluate and save data with ROHDEgraph and ROHDEapp

3 Zone Control Option for ROHDE model Kilns - Can only be added as an option when ordering a NEW kiln.

3 Zone Control option INCLUDES Controller ST 630 (do not change the Controller Option to ST630 - leave as default controller option)

How Does Zone Control Work

Zone Control kilns have a thermocouple in each section of the kiln and cycle the power to each section on and off semi-independently as if it were an individual kiln. When you have have a 3 section kiln and the bottom section is firing a little cooler than the middle and and top section. With zone control turned on, the controller will turn off power to the middle and top sections until the bottom section has caught up and then turn the power to all 3 sections back on. This ensures that the temperature difference between the sections never gets too great.

Zone Control cannot be added later as it requires the changing of several internal compenents most notable because the kiln needs to have a minimum power rating known as 'the loss to watt ratio' in order for the kiln to keep up with the program when sections are turned off to balance the temperature.

3 Zone Control Option for ROHDE model Kilns - Can only be added as an option when ordering a NEW kiln.

Kiln as standard 

Without ELS Door Opening to the Left 

Exhaust Air Flap Handle Control for ELS range 

Can only be operated with a TC507 or TC630 controller using additional switch outputs 

Air supply and exhaust air flap handle control

For ELS range 

Can only be operated with a TC507 or TC630 controller using additional switch outputs

Cooling System for ELS 480 S 

Fan to be controlled from kiln controller - only available if combined with air supply and exhaust air flap handle control and ST 630 controller.

Flexible exhaust air hose, 70mm dia,

Sold per metre

To connect to exhaust air socket 

Hood for Chimney for ELS-S range of kilns 

150mm dia

Socket to connect to chimney at back

Stainless Steel Exhaust Air Hood suitable for ELS330S ELS480S

Rohde Exhaust aiir hoods for electric frontloaders KE and ELS ranges

The robust stainless steel exhaust air hoolds cover the entire ceiling area of the frontloader absorbing exhaust air from the kiln.  The ROHDE in-frame  ventilated side walls direct the heat produced inside the kiln into the ceiling area.  The exhaust air hood then absorbs and discharges it through a connected tube.  

Exhaust air hoods can be connected to other pipes using a standardised socket.  This should be done by a company specialising in ventilation and chimney systems.

Construction properties are perfectly matched to ROHDE Frontloaders allowing optimum removal of exhaust air, e.g. for Paperclay applications.

Rohde Exhaust aiir hoods for electric frontloaders KE and ELS ranges

The robust stainless steel exhaust air hoolds cover the entire ceiling area of the frontloader absorbing exhaust air from the kiln.  The ROHDE in-frame  ventilated side walls direct the heat produced inside the kiln into the ceiling area.  The exhaust air hood then absorbs and discharges it through a connected tube.  

Exhaust air hoods can be connected to other pipes using a standardised socket.  This should be done by a company specialising in ventilation and chimney systems.

Construction properties are perfectly matched to ROHDE Frontloaders allowing optimum removal of exhaust air, e.g. for Paperclay applications.

• 5 x 580mm x 350mm kiln shelves (2 per layer)
• 18 x 25mm props
• 18 x 50mm props
• 18 x 75mm props
• 18 x 100mm props

Drawer floor to moved out electrically 

only available with models:

ELS-330S

ELS-480S

ELS-750S

ELS-1000S